

Air Filter ADP152234 Blue Print
No specifications available yet
Please your vehicle
Supplementary Article/Supplementary Info | With gaskets/seals |
Opening Temperature [°C] | 92 |
Housing Type | Without housing |
application | Thermostat |
Guarantee | 2 years |
Manufacturer | Manufacturer number | Price |
---|---|---|
ASHIKA | 38-03-320 | |
AUTOMEGA | 160020310 | |
BLUE PRINT | ADM59214 | |
BOUGICORD | 161095 | |
CALORSTAT by Vernet | TH5750.92J | |
CAUTEX | 756891 | |
DAYCO | DT1028V | |
DIPASPORT | TRM136N | |
Dr!ve+ | DP2310.14.0294 | |
FAE | 5305192 | |
FARE SA | 22004 | |
FEBI BILSTEIN | 18979 | |
FISPA | 94.323 | |
GATES | TH12592G1 | (this product) |
HERTH+BUSS JAKOPARTS | J1533025 | |
HOFFER | 8192323 | |
JAPANPARTS | VT-320 | |
JAPKO | 38320 | |
JP GROUP | 1514600310 | |
KAMOKA | 7710069 | |
KAVO PARTS | TH-4521 | |
LORO | 017-025-0003 | |
MAGNETI MARELLI | 352027091000 | |
MALÒ | TER092 | |
MAXGEAR | 67-0060 |
Manufacturer | Manufacturer number | Price |
---|---|---|
MAXGEAR | 67-0004 | |
MAXGEAR | 67-0044 | |
MEAT & DORIA | 92323 | |
METZGER | 4006053 | |
MEYLE | 728 288 0000 | |
MOTAQUIP | VTK61 | |
Metalcaucho | 30280 | |
NPS | M153A17 | |
QUINTON HAZELL | QTH578K | |
SASIC | 9000713 | |
SIDAT | 94.323 | |
STC | T430280 | |
STELLOX | 23-40006-SX | |
SWAG | 50 91 8979 | |
TOPRAN | 300 597 | |
TRISCAN | 8620 5788 | |
TRISCAN | 8620 5791 | |
VALEO | 820547 | |
VEMO | V25-99-1705 | |
WILMINK GROUP | WG1091716 | |
WILMINK GROUP | WG2231073 | |
WILMINK GROUP | WG1445811 | |
WILMINK GROUP | WG2113070 | |
WILMINK GROUP | WG1409253 | |
WILMINK GROUP | WG1795718 |
FORD |
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
FORD USA |
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||||
MAZDA |
|
1001993 | FORD |
---|---|
1663819 | FORD |
948M8575AA | FORD |
YF0915171 | MAZDA |
With more than 100 years of experience, Gates is one of the largest manufacturers of drive belts, distributors and relatives in passenger cars. Over 35 automotive brands make use of distributor straps, multi-straps, tensioners and tension rollers produced by Gates at the first installation. The same products are then sold under the Gates label to the private market.
In addition to loose belts, spanners and related, Gates also sells complete kits to renew the engine's drive. These kits are especially popular with garages and service points because they guarantee that all crucial parts of the engine are in top condition. An additional advantage is that a complete installation kit is often more advantageous and always contains the right products, specific to your vehicle.
Gates products distinguish themselves in the following areas:
- Top quality OE products
- OE durability
- Complete distribution and Multirim replacement kit
- Also available in full set water pumps available at reduced rate
- Substantially cheaper than an original Belt (set) from the dealer
At the moment we have the following Gates products in our range:
- Distribution & Distribution
- Multiriemen & Multiriemsets
- Teamrolls & Walkrolls
- Thermostats
Expected delivery date:
30-07-2025
Thermostat works properly (of course) It is nice that there are two seals, with minimal difference, but unfortunately no assembly instructions which to use. This would be useful for people who do not replace thernostats every day. It would be a shame if just too large a seal put too much pressure on the house and the house / lid would give way or break. Too bad if a seal that is just too small causes leakage, and that this can only be seen after heating. A tel. To Winparts for info. It turned out that this depends on the type of thermostat housing the car has. The advice was: first try the thermostat-mounted version if it is tight, then that's the good one. A matter of fitting and feeling. But that applies to diameter. Whether the lid also gives the right pressure on the thickness of the seal ring was the question, but it turned out to work out well.