Transmission Stands: Buy Quality Parts at Winparts

Transmission stand worn

The transmission stand is made of rubber parts, which are subject to wear. Due to all the vibrations and shocks that the stand absorbs, the part can sometimes break. For example, the rubbers can dry out and tear. A worn stand can be recognized by a thumping sound when accelerating or braking. In addition, you may notice vibrations in the gear lever and in the interior while you are driving.

In the case of a worn transmission stand, it is very important that it is recognized and replaced in time. If you allow the part to wear even further, there is a good chance that the stand will break off. With a broken stand you run the risk of serious damage to other car parts because vibrations will occur throughout the car.

Replace transmission stand

We would advise you to replace the transmission stand every 90,000 to 110,000 kilometers. You can replace the transmission stand yourself with the right materials and knowledge. In short, the steps for replacing the stand are as follows:

1. Place the car on a bridge or raise it with a car jack and axle stands.

2. Make sure that the transmission is supported with a car jack or bottle jack before you start working with the stand.

3. Loosen the nuts holding the bracket.

4. Remove the old transmission stand and position the new bracket.

5. Use a torque wrench to retighten the nuts.

6. You can now lower the car again.

Buy transmission stand

Buying a new transmission stand is easy at Winparts. In our range you will find supports for both manual and automatic transmissions. Enter the car model on the website and the correct parts for your vehicle will be displayed. You will also find other parts for the transmission, such as wheel bearings, CV joints, gear control change cables and clutch rods at Winparts.

Gearbox mount

The name says it all, the transmission stand provides good support for the transmission. The support ensures that the shocks and vibrations during driving are absorbed. In this way, the surrounding parts of the transmission are well protected against damage. In addition, the transmission stand ensures that you are not bothered by these vibrations and shocks in the car and the driving comfort is increased. The transmission stand is made of rubber parts, which can dry out or tear. Is the stand damaged? Make sure to replace it with a new one as soon as possible. This prevents further damage to the car parts. Simply enter the car model, the correct parts for your car will then be displayed.

961 - 980 / 1478 products

Filter

0 filters selected

Block view
List view

gearbox support

Material: Steel Elastomer
Outer diameter [mm]: 65
Fitting Position: Rear
Inner diameter [mm]: 39
Bearing Type: Rubber-metal Bearing
Guarantee: 2 years
Length [mm]: 95
Thickness [mm]: 40
External Thread Size: M10 x 1,5
Commercial warranty: 3-year commercial warranty

€ 11,²⁴

In stock

Gearbox mount

gearbox support

€ 89,49

gearbox support

€ 33,30

gearbox support

€ 94,46

gearbox support

€ 79,61

gearbox support

€ 45,83

gearbox support

€ 75,49

gearbox support

€ 74,97

gearbox support

€ 33,43

gearbox support

€ 28,40

gearbox support

€ 61,18

gearbox support

€ 58,57

gearbox support

€ 100,62

gearbox support

€ 58,00

gearbox support

€ 67,82

gearbox support

€ 11,24

gearbox support

€ 115,78

gearbox support

€ 71,55

gearbox support

€ 44,08

gearbox support

€ 29,34

gearbox support

€ 42,06

€ 89,⁴⁹

€ 33,³⁰

€ 94,⁴⁶

€ 79,⁶¹

€ 45,⁸³

€ 75,⁴⁹

€ 74,⁹⁷

€ 33,⁴³

€ 28,⁴⁰

€ 61,¹⁸

€ 58,⁵⁷

€ 100,⁶²

€ 58,⁰⁰

€ 67,⁸²

€ 11,²⁴

€ 115,⁷⁸

€ 71,⁵⁵

€ 44,⁰⁸

€ 29,³⁴

€ 42,⁰⁶