Looking for a clutch releaser? Order here

Recognize a broken release bearing

The clutch release can usually maintain its operation well for about 100,000 km. However, a defect cannot be prevented. The most common cause of a defect bearing is therefore fatigue. Over time, the grease between the parts will lose its lubricating effect, causing excessive friction. Furthermore, driving style can have a major influence on premature failure of this component. You can prevent premature failure by letting the car idle at traffic lights and crosswalks while you wait. Long standstill of the car is also unfavorable, so you run the risk of rust formation between the gear shaft and the bearing.

When to replace the clutch release bearing?

A defective clutch release bearing can be recognized by a rattling, whistling or squeaking sound when pressing the clutch, which becomes more and more audible over time. This noise is caused by the part being worn out. When the clutch release bearing is worn on the guide bush, pressing the coupling can also feel rough or heavy. Continuing to drive with a defective thrust bearing can cause severe wear and even damage to the transmission. It is therefore important that you replace the bearing in time to prevent further damage to your car.

Replace clutch release bearing

A release bearing is always replaced, as this part cannot be repaired. Replacing the bearing is a time-consuming job that requires the gearbox to be completely disengaged. We therefore advise you to replace other gearbox and clutch parts simultaneously during this job in order to reduce costs.

It is advisable to avoid buying the release bearing second-hand. With the quality of well-known brands such as Febi, LUK, Sachs and SKF, you will avoid unpleasant surprises. Our webshop offers a wide range of quality thrust bearings for competitive prices. Enter your license plate number or car model on the website, the thrust bearings suitable for your car will then be displayed.

Clutch release bearing

You must replace a release bearing on time. The bearing is an important part in your vehicle, as it ensures that the clutch disc is released. This means that the release bearing ensures that your car can be put into gear. It is therefore important that this part works properly. At Winparts you will find a wide range of clutch releasers from quality brands such as Febi, Sachs, LUK and SKF. Curious which release bearing is suitable for your vehicle? Then enter your license plate or car model in our handy license plate check and the suitable products for your car will be shown.

2461 - 2480 / 2486 products

Filter

0 filters selected

Block view
List view

Central Slave Cylinder, clutch FTE CLUTCH ACTUATION 1200051 Valeo

Material: Aluminium
Supplementary Article/Info 2: With sensor
Guarantee: 2 years
Fill Medium: Mineral Oil
For manufacturer number: MZA51011.3.3
Cable length (mm): 220
Hole diameter [mm]: 51

€ 668,⁵⁴

Not available

Clutch release bearing

Pressure group 124 0286 10 LUK

€ 234,06

Releaser 1850 282 189 Sachs

€ 26,58

Clutch Pressure Plate 8021 Kawe

€ 1.016,17

Thrust bearing

€ 18,76

Clutch Pressure Plate 1882 600 124 Sachs

€ 451,79

Clutch Pressure Plate 105336 FEBI

€ 276,90

Clutch Pressure Plate 8087 Kawe

€ 468,11

Central Slave Cylinder, clutch

€ 318,93

Shaft Seal Set, clutch

€ 34,96

Central Slave Cylinder, clutch 810012 Valeo

€ 104,03

thrust bearing 3100 007 203 Sachs

€ 257,67

Pressure group 6342 Kawe

€ 216,44

Central Slave Cylinder, clutch

€ 75,25

Central Slave Cylinder, clutch

€ 76,26

Clutch Release Bearing 9901 Kawe

€ 177,90

Release bearing

€ 18,90

Releaser ADS73307 Blue Print

€ 23,27

Clutch Release Bearing

€ 75,62

Central Slave Cylinder, clutch FTE CLUTCH ACTUATION 1200051 Valeo

€ 668,54

Central thrust bearing, clutch 1100329 Valeo

€ 138,89

€ 234,⁰⁶

€ 26,⁵⁸

€ 1.016,¹⁷

€ 18,⁷⁶

€ 451,⁷⁹

€ 276,⁹⁰

€ 468,¹¹

€ 318,⁹³

€ 34,⁹⁶

€ 104,⁰³

€ 257,⁶⁷

€ 216,⁴⁴

€ 75,²⁵

€ 76,²⁶

€ 177,⁹⁰

€ 18,⁹⁰

€ 23,²⁷

€ 75,⁶²

€ 668,⁵⁴

€ 138,⁸⁹